The Brew Cave^®

The Brew Cave^® is the largest kegerator on the residential cooler market. With shelving, it can hold over 30 cases of beer, plus 6 or more kegs. Its refrigeration is designed to hold the inside at 32 degrees Fahrenheit, so you know your beer is optimized for maximum refreshment, and with modular panels that consist of 4” thick vapor-proof insulation, you can rest assured that they’ll stay that way. The Brew Cave^® unit is shipped to you in a knocked-down panel configuration, but can be easily assembled using the included hex wrench.

The Brew Cave^® includes a draft beer dispensing system for convenience and can be retrofitted with more taps. It also has a locking glass door to deter would-be beer thieves. Whether you want to entertain guests, run a small bar, share your home brews or hog it all to yourself, the Brew Cave^® is your beer storage solution. Read on for detailed specifications or buy online.

General

Brew Caves^® are constructed of prefabricated, precision-formed, modular panels designed for accurate, rapid field assembly. Brew Caves^® are test assembled at the factory for quality assurance.

Drawings and Instructions

Each Brew Cave^® includes a set of installation instructions and a lay-out drawing. All panels have a panel identification number corresponding with the lay-out drawing to facilitate rapid and accurate field erection.

Panel Construction

Each panel consists of inner and outer metal skins, a 4″ insulation core, and equipped with cam-action locking devices. The locking devices are operable from inside the Brew Cave^®. A hex wrench to operate these cams is supplied. Press-fit plug buttons are provided to seal the wrench holes after assembly is complete. The Brew Cave’s^® construction is approved by the National Sanitation Foundation International and shall bear the NSF^® Seal of Approval.

Panels are connected to one another by placing the tongue of the insulation core of one panel into the groove of the core insulation of the adjacent panel. The resultant tongue and groove joint is sealed at both sides by double barreled NSF^® approved gaskets. In order to avoid future swelling and mold formation, no wood is used in the manufacture of the tongue and groove panel profile.

Floor Screeds

Floor screeds are provided for all floorless Brew Caves^®. These screeds are vinyl, and have NSF^® approved cove both inside and out.

Panel Finish

Standard metal finish of the panels for interior or exterior walls and ceilings is black stucco embossed galvanized steel. Additional color options are available.

Insulation

Extruded Polystyrene: All wall and ceiling insulation is 4” thick, high quality, rigid extruded polystyrene, 1.6 lb density. K factor of not more than .139 and an R factor of not less than 7.2 per inch, initial fresh R-28.8 minimum total wall R factor. Vapor transmission shall be less than 1 perm and foam core material must meet UL 5 flame spread rating with average smoke rating less than 165. (UL 723)(UL 723)

Box Size

6’10” x 4’10” x 7’6” without a floor

Glass Doors

Anthony Model 403B normal temp, 30”x81” lockable glass entry door with LED lights. 2-pane heat reflective with argon fill, trimline black handle and frame.

Shelving

Shelving fits the back and two side walls, 3 shelves for each wall. Includes two 18” x 48” x 74” black shelves and one 18” x 36” x 74” black shelf.

Refrigeration

Pre-assembled outside refrigeration system, medium temperature, 1 phase, 3/4 horsepower, hermetic 208/230 volt, includes Copeland condensing unit. This must be installed by a licensed HVACR contractor.

Beer Dispensing Kit

Aluminum CO2 tank (empty), keg coupler, double gauge CO2 regulator, chrome faucet head, faucet knob, 5” shank, beer line with connectors, air line with clamps, tap soother faucet cap, 6” wall mount drip tray (stainless steel with drain), drip tray dimensions: 11”H, 6”W, 4 3/4”D. Multiple faucet kits may be installed aftermarket.

Call 800.521.2665 for a dealer near you or request a quote below.